Curb Ramp™ Polyurethane Adhesive
Safety Data Sheet
PRODUCTION AND COMPANY IDENTIFICATION
PRODUCT NAME: Curb Ramp™ Polyurethane Adhesive
CURB RAMP™: 1 (877) 356-9301
24 HR. EMERGENCY TELEPHONE NUMBERS
POISON CONTROL CENTER (MEDICAL): (877) 800-5553
CHEMTREC (US TRANSPORTATION): (800) 424-9300
Causes skin irritation. May cause an allergic skin reaction. Causes serious eye irritation. Harmful if inhaled. May cause allergy or asthma symptoms or breathing difficulties if inhaled. May cause respiratory irritation. May cause damage to respiratory system through prolonged or repeated exposure.
PREVENTION: Do not breathe mist, vapors or spray. Wash hands thoroughly after handling. Use only outdoors or in a well-ventilated area. Wear protective gloves, protective clothing, eye protection and face protection. In case of inadequate ventilation wear respiratory protection.
RESPONSE: IF ON SKIN: Wash with plenty of soap and water. Take off contaminated clothing. If skin irritation or rash occurs: Get medical attention. IF INHALED: Remove person to fresh air and keep comfortable for breathing. If experiencing respiratory symptoms: Call a POISON CENTER or doctor. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical attention.
FIRST AID MEASURES
EYES: Immediately flush eyes with plenty of water. Remove contact lenses, if present. Seek medical attention if irritation persists.
SKIN: Immediately flush with plenty of water. Remove contaminated clothing and shoes. Seek medical attention if rash or irritation occurs.
INGESTION: Give one or two glasses of water to drink. Never give anything by mouth to an unconscious person. Obtain medical attention. Do not induce vomiting unless instructed to so by poison center or physician.
INHALATION: Move person to fresh air. If breathing is difficult, oxygen should be administered by qualified personnel. Obtain medical attention. Symptoms can be delayed for several hours.
FIRE FIGHTING MEASURES
EXTINGUISHING MEDIA: Water fog, foam, dry chemical or carbon dioxide.
HAZARDOUS COMBUSTION PRODUCTS: Carbon oxides, nitrogen oxides, isocyanates and trace amounts of hydrogen cyanide.
EXPLOSION HAZARDS: Water contamination produces carbon dioxide gas. This may cause pressurization or explosion of containers.
FIRE FIGHTING EQUIPMENT: Exposed firefighters must wear NIOSH approved positive pressure self-contained breathing apparatus with full-face mask and full protective clothing.
ACCIDENTAL RELEASE MEASURES
SMALL SPILL: Isolate the area and prevent entry of unnecessary and unprotected personnel. Do not walk through or otherwise scatter spilled product. Absorb with dry chemical absorbent, earth, sand or any other inert material. Place in a chemical waste container. Allow to stand uncovered for 48 before closing container.
LARGE SPILL: Isolate the area and prevent entry of unnecessary and unprotected personnel. Do not walk through or otherwise scatter spilled product. Create a dike or trench to contain product. Prevent entry into waterways, sewers, basements or confined areas. Absorb with dry chemical absorbent, earth, sand or any other inert material. Place in a chemical waste container. Allow to stand uncovered for 48 before closing container.
GENERAL PROCEDURES: Clean spill area with decontamination solution. Suggested formulation: Sodium carbonate (5 – 10%) liquid detergent (1 – 2%), water (88 – 94%). Alternate formulation: Concentrated ammonia (3 – 8%), liquid detergent (1 – 2%), water (90 -96. Ensure adequate ventilation to prevent overexposure of ammonia.
SPECIAL PROTECTIVE EQUIPMENT: Wear protective equipment listed in Section B.
HANDLING AND STORAGE
HANDLING: Do not get in eyes, on skin or on clothing. Wash hands before eating, drinking or smoking. Do not breathe vapors or mists. Use only with adequate ventilation. Keep container closed when not in use. Do not reseal if contaminated. Keep away from heat and flame.
STORAGE: Store in tightly closed containers in a cool, dry and well-ventilated area away from heat or sources of ignition. Keep out of direct sunlight.
STORAGE TEMPERATURE: 4.4oC (40oF) Minimum to 37.8oC (100oF) Maximum.
ENGINEERING CONTROLS: Local exhaust ventilation used in combination with general ventilation as necessary to control air contaminants.
PERSONAL PROTECTIVE EQUIPMENT
EYES AND FACE: Wear a face shield and chemical safety glasses or goggles.
SKIN: Wear impervious gloves. Cover exposed skin.
RESPIRATORY: For airborne exposure above the permissible exposure limit(s), wear a NIOSH approved purifying respirator equipped with organic vapor cartridges. For situations where the atmosphere levels may exceed the level for which an air-purifying respirator is effective, use a positive-pressure air-supplying respirator.
WORK HYGIENIC PRACTICES: Avoid eating, drinking or smoking while using this material. Wash hands thoroughly after handling.
STABILITY AND REACTIVITY
HAZARDOUS POLYMERIZATION: Can be caused by elevated temperatures.
CONDITIONS TO AVOID: Temperatures above 300oF (148.9oC).
HAZARDOUS DECOMPOSITION PRODUCTS: Carbon oxides, nitrogen oxides, isocyanates and trace amount of hydrogen cyanide.
INCOMPATIBLE MATERIALS: Amines, strong acids, strong bases, oxidizing agents and peroxides.
DISPOSAL METHOD: Dispose in accordance with local, state, provincial or national regulations.
EMPTY CONTAINER: Decontaminate and pass to an approved drum recycler or destroy.
RCRA/EPA WASTE INFORMATION: If discarded in its purchased form, this material is not a RCRA hazardous waste.
GENERAL COMMENTS: The generation of waste should be avoided or minimized whenever possible. Chemical waste, even small quantities, should never be poured into drains, sewers or waterways.
The information in this SDS was obtained from sources that we believe are reliable. The information is provided without warranty, implied or expressed, concerning accuracy. The manufacturer assumes no legal responsibility for use or reliance on this information. This SDS is provided solely for the purpose of conveying health, safety and environmental information. This SDS is not a specification data sheet. Some of the information and conclusions may be derived from sources other than test data on the material itself.